收藏本站
AT25DF321
If the address specified by A23-A0 points to a memory location within a sector that is in the pro-
tected state, then the Block Erase command will not be executed, and the device will return to
the idle state once the CS pin has been deasserted.
The WEL bit in the Status Register will be reset back to the logical “0” state if the erase cycle
aborts due to an incomplete address being sent or because a memory location within the region
to be erased is protected.
While the device is executing a successful erase cycle, the Status Register can be read and will
indicate that the device is busy. For faster throughput, it is recommended that the Status Regis-
ter be polled rather than waiting the t BLKE time to determine if the device has finished erasing. At
some point before the erase cycle completes, the WEL bit in the Status Register will be reset
back to the logical “0” state.
The device also incorporates an intelligent erasing algorithm that can detect when a byte loca-
tion fails to erase properly. If an erase error arises, it will be indicated by the EPE bit in the
Status Register.
Figure 8-3.
CS
Block Erase
0
1
2
3
4
5
6
7
8
9
10 11 12
26 27 28 29 30 31
SCK
OPCODE
ADDRESS BITS A23-A0
SI
C
C
C
C
C
C
C
C
A
A
A
A
A
A
A
A
A
A
A
A
MSB
MSB
SO
HIGH-IMPEDANCE
8.3
Chip Erase
The entire memory array can be erased in a single operation by using the Chip Erase command.
Before a Chip Erase command can be started, the Write Enable command must have been pre-
viously issued to the device to set the WEL bit of the Status Register to a logical “1” state.
Two opcodes, 60h and C7h, can be used for the Chip Erase command. There is no difference in
device functionality when utilizing the two opcodes, so they can be used interchangeably. To
perform a Chip Erase, one of the two opcodes (60h or C7h) must be clocked into the device.
Since the entire memory array is to be erased, no address bytes need to be clocked into the
device, and any data clocked in after the opcode will be ignored. When the CS pin is deasserted,
the device will erase the entire memory array. The erasing of the device is internally self-timed
and should take place in a time of t CHPE .
The complete opcode must be clocked into the device before the CS pin is deasserted, and the
CS pin must be deasserted on an even byte boundary (multiples of eight bits); otherwise, no
erase will be performed. In addition, if any sector of the memory array is in the protected state,
then the Chip Erase command will not be executed, and the device will return to the idle state
once the CS pin has been deasserted. The WEL bit in the Status Register will be reset back to
the logical “0” state if a sector is in the protected state.
While the device is executing a successful erase cycle, the Status Register can be read and will
indicate that the device is busy. For faster throughput, it is recommended that the Status Regis-
11
3669B–DFLASH–6/09
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT25F1024AN-10SU-2.7 IC FLASH 1MBIT 33MHZ 8SOIC
AT25F2048N-10SU-2.7 IC FLASH 2MBIT 33MHZ 8SOIC
AT25F4096W-10SU-2.7 IC FLASH 4MBIT 33MHZ 8SOIC
AT25HP512W2-10SI-2.7 SL383 IC EEPROM 512KBIT 10MHZ 16SOIC
AT26DF081A-SSU IC FLASH 8MBIT 70MHZ 8SOIC
AT26DF161-SU IC FLASH 16MBIT 66MHZ 8SOIC
AT26DF161A-MU IC FLASH 16MBIT 70MHZ 8QFN
AT26DF321-SU IC FLASH 32MBIT 66MHZ 8SOIC
相关代理商/技术参数
AT25DF512C-MAHNGU-T 功能描述:IC FLASH 512KB 8UDFN 制造商:adesto technologies 系列:- 包装:带卷（TR） 零件状态:有效 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-UFDFN 裸露焊盘 供应商器件封装:8-UDFN（2x3） 标准包装:5,000
AT25DF512C-MAHNGU-Y 功能描述:IC FLASH 512KB 8UDFN 制造商:adesto technologies 系列:- 包装:托盘 零件状态:停产 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-UFDFN 裸露焊盘 供应商器件封装:8-UDFN（2x3） 标准包装:490
AT25DF512C-MAHN-T 功能描述:IC FLASH 512KB 8UDFN 制造商:adesto technologies 系列:- 包装:剪切带（CT） 零件状态:有效 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-UFDFN 裸露焊盘 供应商器件封装:8-UDFN（2x3） 标准包装:1
AT25DF512C-MAHN-Y 功能描述:IC FLASH 512KB 8UDFN 制造商:adesto technologies 系列:- 包装:托盘 零件状态:停产 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-UFDFN 裸露焊盘 供应商器件封装:8-UDFN（2x3） 标准包装:490
AT25DF512C-SSHN-B 功能描述:IC FLASH 512KB 8SOIC 制造商:adesto technologies 系列:- 包装:管件 零件状态:有效 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:98
AT25DF512C-SSHNGU-B 功能描述:IC FLASH 512KB 8SOIC 制造商:adesto technologies 系列:- 包装:管件 零件状态:有效 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:98
AT25DF512C-SSHNGU-T 功能描述:IC FLASH 512KB 8SOIC 制造商:adesto technologies 系列:- 包装:带卷（TR） 零件状态:有效 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:4,000
AT25DF512C-SSHN-T 功能描述:IC FLASH 512KB 8SOIC 制造商:adesto technologies 系列:- 包装:剪切带（CT） 零件状态:停产 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:512K（64K x 8） 速度:85MHz 接口:SPI 串行 电压 - 电源:1.65 V ~ 3.6 V 工作温度:-40°C ~ 85°C（TC） 封装/外壳:8-SOIC（0.154"，3.90mm 宽） 供应商器件封装:8-SOIC 标准包装:1